Denali
Denali SoundBomb Split Dual-Tone Air Horn - TT-SB.10100.B
Item: #2091566 | Part Number: TT-SB.10100.B$108.99
Description
The DENALI SoundBomb split dual-tone air horn produces an earsplitting 120 decibels of sound (four times louder than your typical motorcycle horn!) in a compact two piece design for motorcycles that have a limited amount of space. Ear splitting performance demands attention to make your presence known and keep you...
Denali SoundBomb Split Dual-Tone Air Horn - TT-SB.10100.B Item # 2091566
Description
The DENALI SoundBomb split dual-tone air horn produces an earsplitting 120 decibels of sound (four times louder than your typical motorcycle horn!) in a compact two piece design for motorcycles that have a limited amount of space. Ear splitting performance demands attention to make your presence known and keep you safe from traffic that might have failed to notice. A 3 foot length of air line is included to allow the powerful horn to be mounted separately from the compressor for the most efficient use of space. The lightweight components can be securely mounted with cable ties. For maximum safety the compact compressor instantly supplies air to the trumpet by pressing the factory horn button. An upgraded Plug-N-Play Wiring Kit is highly recommended and simple to connect. Significantly improve your safety and visibility with the SoundBomb split dual tone air horn from DENALI!
Features:
- Sleek all black construction
- Demands attention that significantly increases awareness
- Tank-less design means no compressed air storage tank to run dry
- Instant performance with no delay in sound output
- Compressor & trumpet are separate units for installation where space is limited
- 3 Feet of air line is included to complete installation on various motorcycles
- Ear splitting performance equal to the DENALI Compact Air Horn
- Intended for motorcycles with limited space
- Great mounting solution for motorcycles with or without fairings
- Can be mounted behind bodywork without inhibiting performance
- Easily mountable with included cable ties
- Designed for use with the recommended optional wiring harness
- Utilizes the factory horn button
Specifications:
- 120 Decibels at 3 feet
- Operating Voltage: 12V
- Power Draw: 20 amps
- Size (Compressor): 4.5″ x 2.9″ x 3.0″
- Size (Acoustic Unit): 4.1″ x 3.7″ x 3.4″
- Housing: Two Part Design
Included:
- Two Piece Electro-Pneumatic Horn
- 12 volt 30 amp relay
- Heat resistant air hose
- Compressor Mounting Hardware
- Acoustic unit mounting hardware
- Additional zip tie mounting option
Part Numbers for Denali SoundBomb Split Dual-Tone Air Horn - TT-SB.10100.B
Reviews
Rated 5 out of
5
by
Devrist from
Always be Heard
Installed a month ago. I never have to worry about being heard again! I have to grin every time I use it. The original horn is still connected, but it is completely drowned out. The existing horn must remain in place or replaced by a resistor otherwise a controller on the CAN bus will detect no current when the horn is pressed and issue a general failure warning on the display.
So far no reliability issues, although almost new. Install is somewhat tedious since there are limited install locations that are not very wet or directly exposed to high engine heat. The 1290 puts out a lot of heat. Expect to spend time planning a suitable install location. The compressor and horn unit are not small. I made my own wiring connections to give me installation flexibility. Cost me an evening of running wires, crimping connectors and applying heat shrink
Date published: 2019-09-07
Rated 5 out of
5
by
Spokes Man from
Split Denali for a new Triumph Bonneville T100
Horns on most bikes are way too wimpy (i.e. not very protective) and the Triumph Bonneville was no exception. I'm a big fan of the SoundBomb but wasn't sure how to best install it. The Bonnie is a naked machine, so I wanted it to be as unobtrusive as possible.
The solution was the Denali split option kit. The compressor fitted nicely on the original Triumph horn mount and I found an ideal mounting point behind the cylinders for the horn unit. I did have to fabricate a special bracket out of aluminum channel to effect a 90 degree turn, but nothing too challenging.
I purchased the Denali pre-made harness, fuse and relay which is well worth the money. This tucked neatly under the saddle, right beside the battery. The connecting air hose from the compressor to the horn ran easily, up under the tank (taking care to avoid the hot spots).
Any concerns that the positioning of the horn behind the cylinders might compromise its effectiveness disappeared the minute I hit the horn. The volume level is sure to alert even the most dozy of drivers ... a magnificent blended two-tone blast (in a classy way) that would give any car horn a run for its money. It makes me grin every time I have cause to use it.
Date published: 2017-06-26
Rated 5 out of
5
by
frozendoc from
LOUD :-)
A bit of a pain to install, even with having the two separate parts. But that's just part of the fun, I guess.
I wouldn't ride a motorbike without one of these. The 'meep meep' horns that come standard are completely inadequate. This one can be heard, and does get people's attention when they are contemplating pulling out of a parking lot, alley, or side street.
Date published: 2019-09-04