Motion Pro Syncpro Carburetor Tuner - 08-0411
$184.99
Motion Pro Syncpro Carburetor Tuner - 08-0411 Item # 141161
Description
- Precise four channel vacuum indicator designed specifically for intake synchronization of engines with multiple carburetors or throttle bodies (maximum vacuum rating for this tool is 40cm Hg)
- New mercury-free design uses non toxic manometer fluid
- For use with any 2, 3 or 4 cylinder four stroke motorcycles
- Spill proof design means the tool can be stored in a horizontal or vertical position
- Easy to read scale for precise synchronization
- Unaffected by barometric pressure changes
- Includes hang hook to clip onto the handlebars for easy use
- Rugged, impact resistant ABS enclosure with convenient storage area for adapters
- Rubber feet on enclosure bottom helps prevent sliding
- Includes manometer fluid, hoses, 5mm adapters, in-line restrictors and instructions
- 5mm adapters are used on many Honda and Suzuki models
- Optional 6mm adapters are available for use on most Yamaha models
- Most Kawasaki models do not need adapters
- Patented design
- Accessories; 08-0168 6mm short adapters(set of 4); 08-0013 5mm brass adapters(set of 4); 08-0040 6mm brass adapters Yamaha (set of 4); 08-0014 replacement hose set, 08-0426 Restrictor Jet (set of 4)
Part Numbers for Motion Pro Syncpro Carburetor Tuner - 08-0411
Reviews
Rated 4 out of
5
by
MLR1 from
Works well
I have had mine for years to sync my 85 Vmax. Works well if you read the instructions and don't rush, take your time. The fluid does dry out so get replacement fluid. Remove hoses and put rubber caps on the end of the sync tool so fluid last longer. Read the instructions.Read the instructions.Read the instructions.
Date published: 2018-12-16
Rated 5 out of
5
by
highspeedhamish from
Syncpro EFI/Carb Tuner
Great tool. Bought to sync efi throttle bodies. Note the back rubber feet on the bottom, they come out and store the supplied carb adapters. I also recommend watching the video from Motion pro as this setup requires several steps to use vs the old, just hook it up and go versions from the past. Body seems solid so with proper use and storage this should last quite awhile.
Date published: 2021-08-14
Rated 5 out of
5
by
mike from
well designed tool
I bought this to sync 4 carbs on a honda cbr1000f. The previous owner had already installed manifold extension hoses up to above the carbs, making it simple to connect to the tool after removing the fuel tank and setting it where the seat was. I had also set all the idle mixture screws to factory specs. It took a bit of fussing to understand how adjusting one carb's throttle plate affects the others, but by going back and forth between them, and every so often going back to adjust the idle RPM, the carbs were synched. Then I went back and fine tuned the mixture screws on each carb as per manual specs (an RPM drop adjustment with the engine running), and then went back and synched all the carbs again. I have noticed a marked improvement in cold starting, and improved off idle throttle response. Well worth the effort and expense if you are so inclined to do your own maintenance.
Date published: 2018-06-07
Rated 5 out of
5
by
Hankon2wheels from
Great Tool, Great results!
Used to balance throttle bodies on my Fz6r and was amazed by its accuracy. Read the instruction thoroughly and it will perform perfectly.
Date published: 2018-03-13
Rated 5 out of
5
by
roadkrome from
very good instructions and easy maintenance.
finally had a chance to try this on my bike, runs as new again. excellent service department.
Date published: 2015-08-05
Rated 4 out of
5
by
Jeff B from
Good Product
I purchased this product to sync the Carbs on my 92 Yamaha Venture. Overall I am happy with the way it worked. I do have a couple suggestions. First, if you are buying this product, I strongly recommend you purchase a re-fill kit as well. When mine arrived it was quite low on fluid and I had to order a kit to fill it prior to use Secondly, I couldn't easily determine from the instructions that the small dampers that come with the tool need to be installed on the Carb end, not the tool end. I had them backwards and the fluid was jumping all over the place. Once I switched them to the Carb end, the readings smoothed right out and work perfectly.
Date published: 2015-08-31
Rated 1 out of
5
by
Gary from
Very dissapointed
Tried to use on 1200 cc 4 cyl Suzuki. Followed instructions to the letter. Could not even sync the tubes as fluid was sucked all the way up the tubes at idle as soon as I hooked the sync manifold to the carb, never lost any fluid as I unhooked it before the fluid was lost. I could not get the fluid to go back down the tubes after I unhooked the tool. Had to resort to my old set of vacuum gauges to do the job. Very disappointed, have read similar reviews on other sites. Tool may work on much smaller engines not sure.
Date published: 2014-02-18
Rated 5 out of
5
by
Bill from
Great product
Great product extremely fast shipping
Worked amazing
Date published: 2022-09-28