This product has been discontinued
Pro Grip 719 Dual Density Road Grips - Open End Item # 220571
Description
Features:
- Reduced Vibration GEL System
- Deep grooves wrap around the gripping area
- Special designed GELS
- 22-25mm i.d.
- 125mm length
Part Numbers for Pro Grip 719 Dual Density Road Grips - Open End
Reviews
Rated 5 out of
5
by
Dennq from
Pro grip review.
Easy install. Vibration dampening. An improvement over the stock grips on my SV 650...
Date published: 2018-05-22
Rated 5 out of
5
by
Mobius1 from
Great!
These grips are easily the best upgrade to any bike I have owned. Easy install, good physical grip and near zero vibrations. No more tingly fingers after hour or two stints on the bike.
Date published: 2015-06-02
Rated 5 out of
5
by
Michael S from
Nice for the cost
The original grips on my bike were showing their age. These are a nice replacement, the soft outer layer is very grippy, almost feels like its sticky. I find that I don't have to grip as hard because of that and with a lighter grip my hands don't go numb and I can ride longer. Easy install, took about 15 minutes. Well worth the money, only have about 500 km on them but even if they don't last long they're cheap and easy to replace.
Date published: 2020-05-17
Rated 5 out of
5
by
Shaner from
Great OEM replacement for my 2004 BMW R1150R
Just remember to confirm the grip diameter on both sides. As mine are the same (heated grips), I needed 2 sets.
Date published: 2019-09-04
Rated 3 out of
5
by
StevieP from
Ok, but didn't dampen vibrations much
I bought these to cut the vibration on a Ducati Monster. They didn't do much for dampening. They are a little more comfortable than stock but my hands would still go numb after a couple hours. Also the outer gel is wearing after around 5000 km. I will have to replace next season I suspect.
Date published: 2019-08-31
Rated 5 out of
5
by
Sonic_55551 from
Good stuff
Install was easy
Results less vibration and feels comfortable
Date published: 2019-08-28
Rated 5 out of
5
by
Carlo from
Excellent
These grips are great, especially after replacing the stock garbage. The grip pattern is offset, so you have to line it up properly, where you feel your hand is comfortable, and conforms to your grip, according to the grip pattern.. As you rotate the grip, out of the box, you will see the pattern direction that suits you, before you put them on your bars. Great product..... they cut down the vibration on my sportbike by at least half, if not more. Very impressed.
Date published: 2019-05-15
Rated 4 out of
5
by
farmer from
Easy install
I have a problem with white nuckle.These grips are larger in diamiter than stock and help a lot with vibration damping.I am riding a lot longer before I have to shake numbness out.
Date published: 2018-08-30
Questions
I'm just wondering if these will fit a 2004 Kawasaki z1000. Thanks.
Yes, if you have stock 7/8'' handlebars, they will fit.
Date published: 2016-02-19
Do they come in a pair. Or individual?
In pairs
Date published: 2017-04-14
is the black/black colour actually all black or half grey like the photo
The photo was most likely shot with a bigger light projector to show the difference between the 2 shades of black. The 2nd color is black, however lighter, so appears grey beside the other black.
Date published: 2019-09-05
is the black/black colour completely black or grey like the picture shown
The middle section of the grip is slightly lighter than the rest but very dark. I would say it is black enough that you cant even tell unless you inspect closely.
Date published: 2019-04-30
Hi, Will they fit my Canam Spyder RT 2010. Do I need to remove the existing grip or does it fit over the existing grip. Are they sold by pair or individually. Thanks Denis
It will fit any 7/8" handle bar. You need to remove existing grips (easiest way is with a compressor and air blower) and they are sold in pairs.
Date published: 2016-08-01