RAM Mounts Self-Leveling Cup Holder Complete Kit - RAM-B-132-309U
$77.99
RAM Mounts Self-Leveling Cup Holder Complete Kit - RAM-B-132-309U Item # 252757
Description
The RAM-B-132-309U is a Complete Kit. You may need to purchase other components to complete your setup
4 Steps to Configure your Mount
A favorite world wide, the RAM Self Leveling Drink Cup holder will bring a smile to anyone's face when they get it. The perfect accessory for any vehicle including motorcycles, ATV's, Big Rigs, and yes, even your prized riding lawn mower. Easily installed and positioned to keep your favorite beverage within reach, this gem even comes with a RAM can insulator. Take a corner as hard as you like, this holder is ready to ride.
Motorcycle Brake/Clutch Reservoir Mount Description:The brake/clutch reservoir mount will accommodate brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter. The mounting hardware for brake/clutch reservoirs includes both standard and metric mounting bolts.
U-Bolt Dimensions:
Accommodates rails from 0.5" to 1.25" in diameter.
Material:
High Strength Composite and Powder Coated Marine Grade Aluminum
Ball Size:
1" Rubber Ball "B" Size
Note:
Cozy included with purchase of this product. To see if the RAM-B-132-309U base will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes' centers have a minimum width of 0.94" and a maximum of 1.58".
Part Numbers for RAM Mounts Self-Leveling Cup Holder Complete Kit - RAM-B-132-309U
Reviews
Rated 5 out of
5
by
gcurly from
quality product
product works great and hold everything from coffee to pop.
Date published: 2015-08-09
Rated 1 out of
5
by
Wasaga Beach 2018 from
Poorly made
This drink holder lasted only one month. Plastic, plastic. With the foam insert in it is too small to hold most take out cups. With a taller drink holder it tips and spills the drink.
I do not recommend this product..
Date published: 2018-12-26
Rated 3 out of
5
by
Doug from
OK but not great.
This product is OK but not great. The ram mounting is excellent but the cup does not always stay level. The inside diameter of the foam insert is too small and most go cups will not fit all the way to the bottom of the holder. Therefore the centre of gravity is too high and it spills. The attachment to the RAM mount is with a screw and that seems a bit Mickey Mouse. It's better than nothing but I suspect there are better products on the market
Date published: 2016-08-17
Rated 2 out of
5
by
Dave from
Poor design
Although the mounting system is great, the cup holder design is outdated. Any cup made of metal or taller than an old school styrofoam coffee cup need not apply. The problem is that there is not enough depth for taller cups or an insert for narrower cups. The cup holder is attached to the mount with a simple screw and some loctite. Should be a screw and locknut. I cut a round hole in the bottom of the cup holder slightly larger than my cup. It now slides down below the centre of gravity and sits snugly. It doesn't bounce and rattle around loosely threatenig to fall out it tip over anymore.
Date published: 2016-05-05
Rated 5 out of
5
by
bob1 from
Used daily on wing to work Perfect
I ride to work daily 40 minutes the cup is perfection Zero regrets stays full on the tightest corners. I put it on at the coffee shop and enjoy every sip of my coffee . The cupholder is deep and works solid . For water bottle i use the foam holder works fine .
Date published: 2022-07-26
Rated 5 out of
5
by
Yves rob from
Très bon produit c'est exactement ce que je recherchais
Date published: 2016-08-13