Vance and Hines Baffle Quiet Insert Twin Slash - Fishtail - 3" - 21899
$113.99
Vance and Hines Baffle Quiet Insert Twin Slash - Fishtail - 3" - 21899 Item # 203527
Description
Features:
- Optional quiet baffle by Vance and Hines
- Sold each
Part Numbers for Vance and Hines Baffle Quiet Insert Twin Slash - Fishtail - 3" - 21899
Fitment for Parts Vance and Hines Baffle Quiet Insert Twin Slash - Fishtail - 3" - 21899
This part fits the following vehicles:
Reviews
Rated 4 out of
5
by
GottaBeKD from
Hard to install but work!
I purchased these baffles for my Vulcan 900c
Original vance and hines twin slash staggered gave me a headache after 30 min. Installed the baffles and sound was still low and strong. Baffles are quiet enough on the highway to not cause issues.
Take off the initial wrap and rewrap with packing tape as tight as you can. Then use wd40 on the baffles and inside your pipes to ease install. Without this install will be a nightmare.
Date published: 2017-05-11
Rated 5 out of
5
by
RBick from
Gotta do, what ya gotta do
Had strata complaints, bought the baffles. Delivered in 5 days in perfect condition. Harder to install than the video ( getting the old ones out was a challenge and the fiberglass bunches up. FYI keep spinning and cut plastic as inserting baffle ). Fired the Bob up, much quieter but still sounds good. Strata can take a hike now
Date published: 2016-05-08
Rated 3 out of
5
by
CrazzzyCat from
Worth it
Noise level decreased from loud to reasonable. If I had to say anything negative, the installation is not as easy as it sounds. Overall very happy with the baffles.
Date published: 2015-08-08
Rated 5 out of
5
by
Dale from
Great sound
Bought Vance Hines Twin Slash 3” for my wifes 1200 sportster was too loud put these Quiet baffles in Sound great now,easy to install I took plastic off baffles and wrapped tightly with packing tape it will slip right in the packing tape burns off in a little bit
Date published: 2018-08-17
Rated 5 out of
5
by
gedubz from
Nice Sound Without Ringing Ears
I got these quiet baffles after riding with the standard aftermarket baffles for a year. Even wearing earplugs the standard aftermarket exhaust was too loud. These still sound great but give my ears a break!
After reading reviews of the install, I had an idea of what to expect. The hard part was lining up the set screw... I would suggest using a square and draw a line down the baffle, so you can line the set screw up properly in the beginning. Once the baffle goes in half way, it is very hard to adjust. I left the plastic wrap on, sprayed some WD-40 on it, and hit it with a hammer and block of wood. Be careful to not hit it too far!
Date published: 2023-05-08
Rated 5 out of
5
by
Jon M from
Trying to be a good neighbor.
These were an easy install since I am putting on new V&H slip ones at the same time. My advice is squeeze tight the Fiberglas wrap with some extra packing tape and make sure the screw hole is lined up before you push it down. Spinning it while it's in the pipe could be a big problem. I haven't installed the pipes yet so I may do a follow up on their actual effectiveness. Oh and buy 2 since they are sold as singles.
Date published: 2017-04-09
Rated 4 out of
5
by
RIZLA from
Gives me the sound I'm looking for but...
Got these baffles on my Vance and Hines slip on mufflers. I'm riding 2016 iron 883. They reduce the decibels and give be a deeper rumbing sound.
BUT pack a lot of patients they a pain in the but to install. You will have to tape down the fiber glass sheets around the baffle very tightly or use fine gauge wire to hold down the fiber glass sheets around the baffle.
In addition i had to remove just a little bit of the fiber glass sheet to make it fit.
Other wise all good.
Date published: 2017-02-15
Rated 5 out of
5
by
RIZLA from
V&H 1.5in. Quiet Baffle - DOES THE JOB BUT....
V&H 1.5in. Quiet Baffle - DOES THE JOB BUT....What a pain in the BUT to install. You will need a lot of patience. You may need to remove a little bit of the fibreglass or tape it down so tight that it will fit in the exhaust pipe. Overall, the bike has come down a few DB's.
Date published: 2017-01-27
Questions
Baffle for TWIN SLASH 3-INCH SLIP-ONS for 2019 softail slim
Yes, the Vance and Hines 1.5in. Quiet Baffle - 21899 is compatible with the Vance and Hines Twin Slash Slip-ons 3 in.
Date published: 2019-12-19
wHAT IS THE DIMENSION
Dimensions:
O.D. on Front: 2 3/8 in.
O.D. on Back: 3 3/8 in.
I.D. of Center Baffle: 1 1/4 in. outlet end
I.D. of Center Baffle: 1 3/4 in. inlet end
Length: 13 1/8 in.
Date published: 2019-05-16
Will these fit in V&H Straightshots?
V&H Straightshots baffles are listed under item #203533
Date published: 2019-10-10
will it fits in twin slash taggered exhaust on a yamaha stryker 2014 ?
You would need one of these baffles for your 2014 Yamaha Stryker:
21897 – Competition Baffle
21899 – Quiet Baffle
Date published: 2020-11-18